Updated November 2026
Kings rooftop tent dimensions come down to three numbers you need to match against your vehicle: the closed shell size, the open sleeping footprint, and the height the tent adds to your roofline. This guide shows you how to find those figures, compare them to your rack and garage clearance, and avoid the fit problems that send tents back to the seller.
Step 1: Find the Closed Shell Dimensions
Start with the closed length, width and height. These numbers decide whether the tent sits within the footprint of your roof rack and whether it clears things like garage doors, tree branches and drive-through lanes. Manufacturers usually list closed dimensions in inches and millimeters on the product page or spec sheet. Measure twice, because a difference of even an inch in width can change how the tent overhangs the rack.
Shopping for one? See our guide: 5 Best 4 Person Rooftop Tent Options for Families and Overlanding.
Step 2: Confirm the Open Sleeping Footprint
Next, check the open length and width. Open dimensions tell you how much sleeping area you get and whether you can lie flat without your feet hitting the ladder or your head hitting the vehicle side. Also check the open height to make sure you can sit up in the tent. Pay attention to whether the listed size refers to the mattress or the full tent floor, since some sites quote one and not the other.
Step 3: Match the Tent to Your Roof Rack and Vehicle
A tent that fits the listing can still fail on your vehicle. Compare these measurements against your setup:
- Roof rack platform length and width. Most tents are designed to sit on a rack or crossbar system with a specified mounting pattern, so confirm the mounting hole spacing and rail dimensions.
- Total roof height with the tent closed. Add the tent height to your vehicle height and check it against parking structures, car washes and low-hanging branches on your trail routes.
- Overhang over the windshield and tailgate. Some owners find the closed tent extends past the rack edges, which affects wind noise and gate or hatch clearance.
- Weight rating. Dimensions do not tell you weight capacity, so check the rated load for your rack and the tent together.
Step 4: Plan the Opening Space
When the tent opens, the shell unfolds outward and the ladder hangs off one end. Check that you have clear space on the side and rear for the shell to swing open, and that the ladder lands on level ground. Owners often report that a tent works well on a flat campsite but becomes awkward on a slope or next to a tree, so plan your typical campsite size before you commit.
Checklist: Measurements to Record
- Closed length, width and height (inches and millimeters)
- Open sleeping length, width and interior height
- Roof rack platform length and width
- Mounting hole spacing and crossbar distance
- Total roofline height with the tent closed
- Rated load capacity for the tent and your rack
- Clearance for opening the shell and ladder
Common Mistakes
- Measuring only the tent and ignoring the rack. The rack is often the limiting factor.
- Forgetting total height. Add the tent to your vehicle height before driving into a garage.
- Comparing mattress size with full floor size. Confirm which figure the listing uses.
- Ignoring wind and drag. Larger closed profiles can increase road noise and fuel use.
- Skipping a test mount. Check fit with the tent loaded on your rack if you can, before a trip.
Recommended Gear
- A tape measure and a notepad: useful for recording your rack and roof height before you shop. View on Amazon
- A roof rack crossbar set that matches the tent mounting pattern: the tent needs a compatible platform, so confirm the spacing first. View on Amazon
- A wind deflector for the front of the tent: it can reduce noise and buffeting on the highway. View on Amazon
For related setup ideas, see Rooftop Tent Mounting Rails: How to Choose and Install Them Safely (2026) and Top 5 Rooftop Tent Wind Deflector Options Compared for 2026.
FAQ
Do I need to measure my roof rack before buying a Kings tent?
Yes. Compare the tent mounting pattern and platform size with your rack, since the rack often limits what will fit even when the tent itself is compatible.
Which dimension matters most for height clearance?
The closed tent height added to your vehicle roofline. Use that total for garage, car wash and low-branch clearance.
Are the listed dimensions the same as the sleeping area?
Not always. Check whether the figure refers to the mattress or the full open floor, and confirm with the manufacturer if the listing is unclear. Consult the manufacturer or a qualified installer for mounting questions.
Conclusion
Kings rooftop tent dimensions are simple to check once you know which numbers to compare: closed size, open sleeping footprint and total roofline height. Record your rack and vehicle measurements first, then match them against the tent specifications. A few minutes of measuring now prevents fit problems on the trail.
